2022-02-17 13:50:11

The good price and quality emark reflector products manufacturer tells you how to install the customized reflex truck reflector

The good price and quality emark reflector products of the vehicle body is a combination of reflective materials installed or pasted on the surface of the vehicle body to enhance the identifiability of the vehicle. In short, it is a emark reflector set on the vehicle body. It can greatly improve the identifiability of large transport vehicles at night, dusk, rain, fog and other low visibility conditions, and can effectively prevent and reduce rear end accidents caused by poor identifiability of large transport vehicles under low visibility conditions. It is an effective means to prevent rear end accidents at night. According to the different composition materials, the body reflex truck reflector are divided into reflective film type body reflex truck reflector and reflector type body reflex truck reflector.


Since the customized emark reflector products on the car body are so important, the majority of drivers, especially truck drivers, must have safety awareness. They must stick customized reflex truck reflector on their cars. Light stickers are not enough, but they should be pasted correctly and accurately, so as to effectively prevent accidents.
How to paste customized reflex truck reflector on the body?
The body reflex truck reflector at the rear of the body shall start with the white unit and end with the white unit. The side may start with a red unit, but the last unit near the rear of the vehicle shall be a white unit, and the intersection of the rear corners of the cargo compartment shall be a white unit.
The following points should be paid attention to when pasting reflex truck reflector on the vehicle body:
1.The customized reflex truck reflector of the vehicle body shall be installed or pasted on the rear and side outer surfaces of the vehicle body that are unobstructed and easy to see
2.Different types or grades of body emark reflectors can be installed or pasted on the rear and side of the body, but the rear body emark reflectors and side body emark reflectors shall choose the same type or grade of body reflective signs respectively
3.After the vehicle is installed or pasted with the body emark reflector products, it is not allowed to drill holes or slots on the body emark reflectors
Guidelines for pasting emark reflectors on the rear body
The minimum height of good price and quality emark reflectors on the vehicle body from the ground is 380mm.
Body emark reflector materials are mainly divided into class I and class II. When class I body reflective marking materials are adopted, the sum of the area with the rear reflector shall not be less than 0.1 ㎡; When the secondary body reflective marking material is adopted, the sum of its area with the rear reflector shall not be less than 0.2 m2.
The customized reflex truck reflector products on the rear body shall be pasted continuously. If they cannot be pasted continuously, they can be pasted intermittently, but the length of each continuous section shall not be less than 300mm, and shall include at least one unit of red and white body reflective signs, and the pasting interval shall not be greater than 100mm. Under special circumstances, red and white units are allowed to be pasted separately, but red and white shall be maintained. The length of each continuous section shall not be less than 150mm, and the pasting interval shall not be greater than 100mm. If it cannot be pasted vertically along the edges on both sides of the rear of the carriage, it can be pasted on the pasteable surface with the width of 50mm closest to the edge, and the upper edge of the body reflective sign shall be close to the upper edge of the rear of the carriage as far as possible.
Guidelines for pasting  reflex truck reflector on side body
The pasting of side body  reflex truck reflector is allowed to be interrupted, but its total length (excluding the interval part) shall not be less than 50% of the vehicle length, the length of each continuous section shall not be less than 300mm, and shall include at least one unit of red and white body emark reflector products. The pasting interval of class II body emark reflectors shall not be greater than 150mm, and the pasting interval of class I body emark reflectors shall not be greater than 300mm, The paste shall be evenly distributed longitudinally as far as possible. Under special circumstances, red and white units are allowed to be pasted separately, but they shall still be red and white. The length of each continuous section shall not be less than 150mm, the pasting interval of secondary body reflective identification materials shall not be greater than 150mm, and the pasting interval of primary body reflective identification materials shall not be greater than 300mm.
The length of  reflex truck reflector products on the side body shall not be less than 1.2m for three wheeled vehicles; The length of the freight car shall be the length of the freight car if the length of the freight car is less than 50% of the length of the car; For the concrete mixer and special operation vehicle without continuous surface on the side body structure, the total bonding length shall not be less than 30% of the vehicle length. The customized reflex truck reflector on the side of the van and van Trailer shall reflect the outline of the cargo box.

keyword:

good price and quality emark reflector, emark reflector products, emark reflector, emark reflectors,customized emark reflector,customized reflex truck reflector,reflex truck reflector

The good price and quality emark reflector products manufacturer tells you how to install the customized reflex truck reflector

Relevant news