Discount road stud reflector company summarizes the precautions for installation of the Best road stud reflector from China

With the wide application of the Best road stud reflector from China in domestic high-grade highways and municipal roads, more attention has been paid to the quality and service life of the Best road stud reflector from China. However, in the actual application process, the Best road stud reflector from China is often damaged and its service life is reduced due to installation problems. Based on years of construction experience, Discount road stud reflector company summarized the problems that often occur in the installation process of the Best road stud reflector from China.

The following are common problems during the installation of the Best road stud reflector from China:

1. The Best road stud reflector from China is installed on the marking. The marking is also a kind of resin material, which is attached to the ground itself, and its connection with the ground is limited. If the road nail is installed on the marking line, the impact force on the Best road stud reflector from China will be completely transferred to the marking line. In this way, the Best road stud reflector from China is easy to be impacted off, and the marking line will also be stuck off.

2. The installation position of the Best road stud reflector from China is uneven. The direct consequence of this is that the force on the Best road stud reflector from China is uneven, and the pressure on the Best road stud reflector from China is almost all concentrated in the convex and concave parts. If large tonnage vehicles are encountered, road stud reflector products is easy to break.

3. The installation position of the Best road stud reflector from China is not clean. The fastness of the Best road stud reflector from China depends on the close combination of the Best road stud reflector from China, glue and the ground. If the installation position is not clean, the dust between them will absorb most of the adhesive force of the glue, resulting in poor adhesion of the Best road stud reflector from China, which is easy to fall off when subjected to external impact.

4. The amount of glue is insufficient or excessive. If the amount is not enough, the firmness of the Best road stud reflector from China bonding will be reduced and its service life will be reduced; If the amount is too much, the excess glue will seep out from around the Best road stud reflector from China, which is easy to rub onto the reflector of the Best road stud reflector from China, affecting its reflective brightness.

5. The glue is applied unevenly. When installing the Best road stud reflector from China, the amount of glue should not only be appropriate, but also be evenly applied, so as to ensure that all parts of the Best road stud reflector from China are evenly stressed and avoid being crushed due to uneven stress.

6. The ambient temperature is not enough when epoxy resin glue is mixed. The epoxy resin glue is a two-component glue. The glue and curing agent should be proportioned according to a certain proportion, and can play their role only after being evenly stirred. However, the epoxy resin glue is hard to be stirred evenly due to its severe condensation in the cold weather in winter, so it must be heated before use to soften the glue.

7. The method of handling the Best road stud reflector from China is not scientific. When handling the Best road stud reflector from China, be sure to handle the two sides without reflectors, so as to avoid glue sticking to the reflectors and affecting the reflective brightness of the reflectors.

8. The installation hole of the Best road stud reflector from China is shallow and thin. This is mainly for the cast aluminum strip foot road stud reflector. The cast aluminum strip foot road stud reflector from china has better impact resistance, compression resistance and longer service life because part of it goes deep into the ground. However, in the installation process, if the hole position is too shallow or too thin, the bottom surface of the Best road stud reflector from China cannot fully contact the ground, which affects the firmness of the bonding.

9. The time for glue curing after installation is not enough. After the installation of the Best road stud reflector from China, the glue needs to be solidified for a period of time to firmly connect the Best road stud reflector from China to the ground. The recommended time is 4 hours. But in the actual process, many people removed the installation isolation facilities less than two hours after installation; In this case, if the Best road stud reflector from China is impacted and rolled by vehicles, it will deform in light cases and fall off in heavy cases.